CH 160 OEM Electric or Engin Powered Sawmill Chipper

 

The CH 160 OEM chipper is powered from a 8" diameter pulley with 4 belts.

Sawmill Model CH 160 OEM-F

The chipper can take 9" wide slabs, the slabs are pulled in by the knives.

Land clearing Model CH 160 OEM-HF/HD

The chipper has a self-contained hydraulic system and hydraulic feed.  The chipper requires a engine producing 35 HP when used at maximum 6 ¼" diameter capacity.   The system includes tank, filter and pump which is driven from the chipper axle.

The Valby CH 160 chipper produces uniform chips which can be used for burning, animal bedding, landscaping and mulch. The chipper can chip soft and hard woods, green or seasoned. The chipper is capable of chipping 6 ¼" diameter round wood. It can handle residue from logging, land clearing, orchards and gardens. The chipper can also handle slabs up to 9" wide.  The material is drawn into the chipper at the speed of 1 to 3 feet per second.   The chipper is self-feeding and draws in the material without pushing by the operator.

Ease of Operation

The low feeding point ensures effortless feeding of the chipper, thus allowing the operator to stand with a straight back. The chipper stands by itself on the ground and is easy to hook up or remove from the tractor. The large feed chute takes most unpruned branches, eliminating time-consuming pruning.

Safety Features

The Valby chippers do not have any knife motion toward the operator. This reduces the risk of material flying back through the feed chute. The discharge height is 86" above ground so the discharge is above eye level. To accomplish safe operation in various wind directions, the Valby chipper's discharge direction is adjustable 360 degrees. The chipper feeds the material smoothly and does not jerk it from the operator's hands.  The knives are counter-sunk into the disk, so the strain of chipping is absorbed by the backside of the knife.

Powerful Chip Discharge

The fan is built into the chipper's disk so it also retains its rotational speed under heavy loads. The chips can be directed in any desired directionas the discharge chute rotates 360 degrees. The chips can be placed near or far by aiming the deflector bonnet.

Ease of Service

The knives can be sharpened about 50 times before replacement. The changing of the knives takes approximately 10 minutes. The knives are easy to get to and no special tools are needed for the change. The discharge chute is easy to remove so the chipper can be stored inside low buildings.

Interchangeable Feed Chutes

The feed chutes of the chipper are on a hinge, so the chute can be folded to the side for access to the anvil and knives. The feed chutes are detachable. One can hook up either feed chute option to an existing machine

The F 150 is a regular drop feed where the knives pull in the material. The HF 160 has a hydraulic power feed roller which feeds in the material.

Hydraulic Power Feed Option

The Valby CH 160 can be ordered with a hydraulic power feed.  The power feed is useful when whole trees with branches are chipped. The hydraulic feed is controlled from a control bar which runs on top of the feed chute. The operator can select feed, stop and reverse from the control bar.  The HF 160 power feed has one large 10 1/8" diameter top feed roller.   The feed roller climbs on top of the material, and the teeth bite into the material and feed it in.

Oil required from the tractor minimum 3; maximum 10, gallons per minute.  The chippers are also available with an internal hydraulic system. The system includes tank, filter and pump which is driven from the chipper axle.  This option is for tractors where the hydraulic flow is insufficient to run the power feed.

 

Specs

Chipper rotor:
Diameter: 26 3/8"
Weight: 220 Lbs.
Knives: two 8 3/4" x 3 7/8" full-size knives
In feed Capacity: 6 1/4" diameter round wood
Anvil: Adjustable boron steel anvil
Bearings: spherical roller
Mean Chip Length: 9/16"
Feed Height: 24" above ground
Discharge:
Adjustable 360 degrees
Height: 37 ¼"
Hydraulic Power Feed HF 160
Power Feed Roller Size: 10 1/8" diameter, 10 3/8" wide
Hydraulic Motor Size: 24 cu. inches/rev.
Weights:
Chipper with standard F160: 710 lb.
Chipper with Self-contained hydraulic system HF 150 power feed:1050 lbs.